Factory Self-Leveling Epoxy Floor, Epoxy Painting Floor

• Customization: Available
• Bonding Function: Structural Adhesive
• Morphology: Liquid
• Model NO.: epoxy floor
• Material: Epoxy
• Classification: Room Curing
• Main Agent Composition: Thermosetting Resin
• Characteristic: Waterproof
• Promoter Composition: Curing Agent
• Composition: Organic Material
• Color: Transparent
• Shelf Life: Six Months
• Component Rate: 3:1
• Package: 5kgs 20kgs
• Lead Time: 3 Days
• Transport Package: 20kg/Set, Carton
• Specification: ROHS, REACH, CPSIA, PAHS
• Trademark: Jinhua glue
• Origin: Shenzhen, Guangdong, China
• HS Code: 3506912000
• Production Capacity: 300 Kilograms Per Month

Product Description

Epoxy Self-leveling Floor Paint
Product formation:
Solvent-free two component paint of epoxy resin, pigments, fillers, additives and active diluent.

Product features:
. High adhesion strength with the primary
. Seamless, Low hardening shrinkage, no easy to crack
. Easy to clean, do not gather dust and bacteria
. Environmental protection non-toxic
. Wear resistance, can withstand the forklift, carts and other tools' long time rolling 
. Anti permeability, corrosion resistance, Oil resistance and water resistance
. Easy to construction and good decoration, the surface is smooth and color bright
. Also can be made for static conductive epoxy floor paint

Using
Mainly used in electronics, electrical appliances, hardware, machinery factory, school, hospital, chemical, pharmaceutical, laboratory, food factory, textile factory, printing factory, chemical plant, computer room, supermarket, parking lot, all kinds of electrical control room, command center And so on the ground has a very high demand for the industry.

Mixing Ratio
Primer: 3:1, usage 0.1kgs/sqm
Mid: 5:1, usage 0.1kgs/sqm
Top Coat: 5:1, usage 0.6~0.8kgs/sqm

Packing
Paint: 5/10/20 kg/bucket  Curing agent: 5/10/20 kg/bucket
Or as customer required

Technical Data:
Color and appearance of paint film          Colors and smooth film
Dry film thickness, mm                    1.5~2mm
Drying time (25 ºC), H                   surface dry≤8h, hard dry≤24h, Fully cured 7days
Adhesion (zoned method), class             ≤1
Impact strength, kg, CM                   ≥70
Compressive strength, M Pa                ≥85
Tensile strength, MPa                     ≥9
Bending hardness, MPa                    ≥7
Wear resistance (Mg, 750g/500r)            ≤20
Water resistance                         48 hrs, no blister, no fall off, no change color
Alkali resistance                         48hrs, no blister, no fall off, no change color
Acid resistance                          48hrs, no blister, no fall off, no change color
Leveling property, min                    ≥5
Hardness (swing rod method)               ≥0.6


Double coating interval time:
Temperature              5ºC             25ºC             40ºC            
Shortest time             32h              18h              6h
Longest time              14d              7d               5d

Surface treatment:
Completely remove the oil pollution on the surface of cement, clean the sand and dust, moisture and so on, to ensure that the surface is smooth, clean, solid, dry, non foaming, not sand, no cracking, no oil. Water content should not be greater than 6%, the pH value is not greater than 10. The strength grade of cement concrete is not less than C20.

Construction condition:
The temperature of the base floor is not less than 5ºC, and at least 3ºC than the air dew point temperature, the relative humidity must less than 85% (should be measured near the base material), fog, rain, snow, wind and rain is strictly prohibited construction.

Construction method:
Brush / roll coating: must achieve the specified dry film thickness.








 

The properties after hardening
1)Hardness	shore D	<85
2) Withstand voltage	KV/mm	22
3) Flexural strength	Kg/mm2	28
4) Volume resistivity	Ohm3	1x10*15
5) Surface resistance	Ohmm2	5X10*15
6)Thermal conductivity	W/M.K	1.36
7)Induced electric loss	1KHZ	0.42
8)Thermal deformation temperature	°C	80
9)Moisture absorption	%	<0.15
10)Compressive strength	Kg/ mm2	8.4

FREE SAMPLE IS AVAILABLE!!!

Jinhua professional produce and market all kinds of epoxy resin AB glue which covers a very large range of applications: Soft AB glue for stickers, LED strip potting, badge, nameplate, nail cutters, keychain!!!

Hard clear resin for LED channel letters, photo frame coating, hand made diamond, jewelry, crafts, nacklace, bangles, bracklets, earrings, rings, miniatures such as simulated water, soup,lquid drinks and fishbows to be used in a child's dollhouse, anything you can image clear and shinning, but cheap and easy to operate!!!

Coating resin for surfboard, paddle, christmas ball, globe, foam products coating, bicycles, boats, golf clubs,skies, snowboards, swimming pool, garage, wood table coating, Epoxy flooring, to make it hard and durable!!!

Special ahhesion for wood, metal, glass, stone and some plastic.With very strong and high durable bond after cured!!!

Flexible potting resin for electronic products such as motors, generators, transformers, swithgeear, insulators, mold filling,LEDs, perfectly to protect the potting items from short circuit, dust, water, and moisture, and giving the potting items a more stable and longer life than unpotted products!!!

Pls contact us to discuss your application for a best EPOXY SOLUTION!!!